Owens Corning Gutter Replacement Nationwide

Owens Corning Gutter Replacement: The Long Beach Owner’s Guide

Owens Corning gutter replacement in Long Beach typically runs $14 – $28 per linear foot installed, which puts most single-story homes between $1,800 and $4,200 depending on roofline length, gutter profile, and downspout count. We stock Owens Corning-compatible aluminum gutter profiles, hangers, end caps, and downspout elbows on our trucks, so most replacements are done in a single visit. The way Long Beach homeowners usually discover the problem is simple: a section pulls away from the fascia after a winter storm, water starts pouring over the edge near a corner, or a rust-through spot finally opens into a visible hole. By the time you’re reading this, chances are you’ve already spotted the tell-tale sag or the damp patch on the soil below.

Call (562) 471-4832

Key takeaways:

• Installed replacement averages $14 – $28 per linear foot in Long Beach
• We carry Owens Corning-compatible profiles and hardware on the truck
• Most full gutter replacements are completed in one day
• Every job includes a written price before work starts, no exceptions

Which Owens Corning Models This Applies To

Owens Corning manufactures two gutter lines worth knowing about. The first is their Classic 5″ K-style aluminum gutter, the workhorse profile you’ll find on most Long Beach ranch homes and mid-century bungalows. The second is the 6″ oversized K-style, which handles steeper roof pitches and heavier rainfall volumes. The compatibility gotcha here is real: Owens Corning hangers and end caps are profile-specific, meaning a 5″ hanger will not seat correctly on a 6″ trough, and mixing them creates exactly the sag-and-leak pattern that fails in the first place.

You’ll find the profile marked on the inside of the gutter channel, near an end cap or miter fitting, usually stamped as “OC 5K” or “OC 6K.” If the stamp has worn off, measure the top opening across the channel; 5-inch and 6-inch dimensions are consistent enough to confirm at a glance. We’ll also match the gauge, typically .027 aluminum for standard and .032 for coastal exposure, which matters in Long Beach because of the salt air coming off the water.

Quick note on sourcing: Crestview Roofing Co Long Beach is an independent service provider, not a factory dealer or affiliate of Owens Corning. We install Owens Corning-compatible parts and genuine profile-matched components, and we’re happy to show you the difference before anything goes on the house.

Signs Your Owens Corning Gutter Replacement Is Failing

• Pulling away from the fascia board. The aluminum channel expands and contracts with Long Beach’s temperature swings, and after a decade or two, the original hanger screws have wallowed out their anchor points. The gutter tilts forward, spills water, and starts levering the entire run loose.
• Water overflowing at inside corners. Inside miter joints fail more often than any other point on a gutter system because they carry the most water volume and the most sealant stress. When you see a steady drip or an actual waterfall at the corner, the joint has opened and caulk alone won’t hold it.
• Rust-through pinholes or long streaks of orange staining. Even aluminum gutters corrode when debris sits in the channel for years and holds moisture against the metal. In Long Beach’s marine layer climate, the moisture tends to linger longer than it would inland, accelerating the pitting.
• Downspout separation or cracked elbows. Plastic or thin-gauge downspout elbows are surprisingly fragile. A ladder against the wrong spot or one hard rainy season with the lower elbow backed up will crack it, and then everything below the break drains straight onto the foundation.
• Sagging between hangers. Owens Corning systems are designed for hangers every 24 to 30 inches. When installers stretch that spacing to save hardware, the channel flexes between supports, holds standing water, and eventually fails at the stress point.

Replacement Cost & What’s Included

Here’s the straight pricing picture for Owens Corning-compatible gutter replacement in Long Beach:

• 5″ K-style aluminum gutter, standard .027 gauge: $14 – $19 per linear foot installed
• 6″ K-style aluminum gutter, standard .027 gauge: $17 – $24 per linear foot installed
• Coastal-grade .032 gauge upgrade: add $3 – $5 per linear foot
• Downspout replacement (each run): $85 – $160 installed
• Full tear-off and disposal of old gutter system: $3 – $5 per linear foot

The range comes down to roof access, linear footage, gutter profile, and whether we’re replacing downspouts at the same time. A one-story Belmont Shore bungalow with a simple rectangle roofline falls at the low end. A two-story Naples Island home with multiple inside miter corners and steep roof access falls at the higher end. You get a written price before any work starts; that number includes tear-off, disposal, all hangers and hardware, sealant at every joint, and the installation itself. The 365-Day Done Right Promise covers the entire job in writing, so if a joint opens or a hanger fails within a year, we fix it at no charge.

DIY or Call Us?

Gutter replacement is not a high-tension-spring situation, but it does involve ladders, roof-edge work, and a few honest dangers. If you want to pre-check before calling, walk the roofline from the ground, note where the sag, staining, or separation is happening, and snap a few photos with your phone. That gives us a head start on the quote. What I’d skip is the ladder work itself: most Long Beach homes sit on stucco walls or soft soil near the foundation line, and a ladder set wrong is the most common way this job goes sideways. Miter joints and hanger replacement also need specific tools and a feel for the metal; if you’ve never worked aluminum channel before, the learning curve is usually more expensive than the labor.

Dylan Pace puts it this way: “If I wouldn’t put it on my own roof, I’m not putting it on yours.” We inspect, we measure, we price it in writing, and then we install it like it’s our own house. Call (562) 471-4832 and we’ll set up a free estimate.

FAQs